Trane Performance Air Handlers Instalační manuál Strana 32
- Strana / 100
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
32 CAH-SVX01B-EN
Installation - Mechanical
TCC Model Assembly Instructions
NOTICE
Roof Curb Structurally Sound
Check with curb manufacturer and job engineer to ensure the roof curb is structurally sufficient
to support the weight of the unit. The curb should be checked to ensure it is level and square.
Curb bowing, buckling, or sagging can lead to unit assembly and operation problems up to
complete failure.
If your nameplate model number begins with TCC, use the assembly instructions below.
TCC Overhang Base on Common Roof Curb
1. A base designed for use with a roof curb allows for 1/2- inch clearance around the full perimeter
of the curb.
2. The end section must be installed first making sure it’s properly aligned with the remainder of
the curb. Anchor this section securely so the base lugs can be used to pull the next section for
base connections.
3. Install 3/16-inch x 1.25-inch grey butyl tape to bottom rail of installed section allowing the tape
to turn up each side wall approximately 8 inches. Remove paper backing from butyl tape. This
will ensure the module-to-module joint is water tight along the bottom.
4. Lift next section onto roof curb using come-alongs to pull securely to first section. See “TCC
Joining Sections - Edge-to-Edge” on page 33 for assembly details.
TCC Flat Base to Steel Dunnage or Concrete Pad
Important: Units must be installed level for proper drainage of condensate from the drain pan
and for squareness of the sections during installation. In addition, each section in a
multi-section unit must be properly supported.
1. A base designed for concrete or steel dunnage has a flat channel base that allows the sections
to be installed level and square. Pad and dunnage should have unit perimeter marked clearly
allowing a completely square installation. See Figure 19 and Figure 20.
2. Install first section and anchor with best method to hold securely.
3. Proceed with remaining sections per installation guidelines.
Figure 19. Steel base to concrete pad Figure 20. Flat base to steel dunnage
Air handler
base structure
Concrete
pad
Air handler
base structure
Dunnage
- Custom Climate Changer™ 1
- Air Handlers 1
- WARNING 2
- WARNING 3
- Table of Contents 4
- CAH-SVX01B-EN 5 5
- 6 CAH-SVX01B-EN 6
- CAH-SVX01B-EN 7 7
- General Information 8
- Pre-Installation Requirements 10
- Resolving Shipping Damage 11
- Storage Recommendations 11
- Preparing the Unit Site 12
- Roof Curb Structurally Sound 13
- Suggested Tools 14
- Installation - Mechanical 15
- Lifting Considerations 16
- Unit Assembly 17
- TCP Standard Roof Curb 18
- TCP Flat Concrete Pad 20
- TCP Wall Section Assembly 25
- TCP Stacked Unit Assembly 31
- Remove shipping blocks 33
- Butyl tape 34
- Insert hardware in each hole 34
- Rod threaded 35
- 62-11x13.38, THD 35
- Lockwasher .625 35
- Nut 62-11 35
- Washer .563 ID x 1.375 OD 36
- Bolt .500-13 x 3.500 Hex 36
- Nut .500-13 Hex Mach 36
- TCC Stacking Procedure 40
- Pipe Cabinet Installation 43
- Duct Connections 46
- Isolator Adjustment 48
- Side Load Filters 50
- 2-inch or 4-inch flat filters 50
- Bag or Cartridge Filters 51
- Outdoor Unit Weather Hood(s) 52
- Coil Piping and Connections 53
- Steam Coil Piping 56
- Breaker Cracking Pressure! 57
- Coil Condensate! 57
- Water Coil Piping 58
- Refrigerant Coil Piping 60
- Valve Damage! 62
- Suction Lines 62
- Installation - Electrical 69
- Penetration Leaks! 71
- Quick Connects 72
- Controls Interface 73
- External Communications Port 74
- Start-Up 75
- Coil-Related Checks 76
- Proper Water Treatment! 76
- Motor-Related Checks 76
- Voltage imbalance = 77
- AvgVoltage× 77
- Tension the Fan Belt 78
- Belt Tension! 78
- Determine Fan Speed 79
- Align Fan and Motor Sheaves 80
- Check Multiple Belts 80
- Traq™ Dampers 81
- Transmitter Sizing 82
- Transmitter Calibration 83
- Constant Factor K 83
- Microbial Growth! 84
- Routine Maintenance 85
- Fan Bearing Lubrication 89
- Bearing Failure! 89
- Bearing Set Screw Alignment 89
- Coil Winterization 93
- CAUTION 97
- Troubleshooting 98
Související produkty a manuály pro Split-systém klimatizace Trane Performance Air Handlers
(78 stránky)Littelfuse FLR 58V Fuseholder Series manuels
Manuels d'utilisation et guides de l'utilisateur pour Matériel Littelfuse FLR 58V Fuseholder Series.
Nous fournissons des manuels en pdf 1 Littelfuse FLR 58V Fuseholder Series à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentáře k této Příručce